1. | Remove the crash pad lower panel. (Refer to the Body group-crash pad) |
2. | Remove the junction box. (Refer to the Body Electrical System group - Fuses and Relays) |
3. | Disconnect the parking brake switch connector (A). |
4. | Remove the parking brake pedal mounting bolts (A) and nut.(B) |
5. |
6. | Remove the parking brake cable adjusting nut(A) and the fixing clip(B), and then remove the parking brake pedal. |
7. | Remove the floor console. (Refer to the Body group - Console) |
8. |
9. | Remove the paring brake cable (B) after removing the cable retainer (A). |
10. | Raise the vehicle, and make sure it is securely supported. |
11. | Remove the parking brake cable (B) after removing the fixing clip (A). |
12. | Loosen the parking brake cable bracket bolts and remove the rear parking brake cable. |
1. | Remove the floor console. (Refer to the Body group - Console) |
2. |
3. | Disconnect the parking brake switch connector (A). |
4. | Remove the parking brake cable (B) after removing the cable retainer (A). |
5. | Remove the parking brake lever assembly after removing the 4 bolts as shown below. |
6. | Raise the vehicle and make sure it is securely supported. |
7. | Remove the parking brake cable(B) after removing the fixing clip (A). |
8. | Loosen the parking brake cable braket bolts and remove the parking brake cable. |
1. | Raise the vehicle, and make sure it is securely supported. |
2. |
3. | Remove the rear brake caliper and Rear disc brake. |
4. | Remove the parking brake cable (B), after removing the fixing clip (A). |
5. | Loosen the hub assembly mounting bolts (A), and then remove the hub assembly and parking brake assembly. |
6. | Remove the adjuster assembly (B) and the lower return spring (A). |
7. | Remove the upper return spring (C) operating lever assembly (D). |
8. | Remove the shoe hold down pin (A) and the spring (B) by pressing and rotating the spring. |
9. |
1. | Install the shoe hold down pin (A) and spring (B) by pressing and rotating the spring. |
2. | Install the operating lever assembly (D) and the upper return spring (C). |
3. | Install the adjuster assembly (B) and the lower return spring (A). |
4. | Install the hub assembly and the parking brake assembly, and then install mounting bolts (A). |
5. | Install the parking brake cable (B), and then install the fixing clip (A). |
6. | Install the rear brake disc, then adjust the rear brake shoe clearance.
|
7. | Install the brake caliper assembly. (Refer to 'Rear brake installation') |
8. | Install the tire and wheel, after installing the plug on the disc. |
9. | If the parking brake shoe or the brake disc are replaced a newly one, perform the brake shoe bed-in procedure.
|
1. | Install the parking brake lever assembly, then tighten the mounting bolts.
|
2. | Install the parking brake cable (B) and then cable retainer (A). |
3. | Apply a coating of the specified grease to each sliding parts (A) of the ratchet plate or the ratchet pawl.
|
4. | Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).
|
5. |
6. | Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary. |
7. | Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully. |
8. |
|
9. | Install the floor console. (Refer to Body group - 'Floor console') |
1. | Install the parking brake cable. |
2. |
3. | Install the floor console. (Refer to the Body group - console) |
4. | Install the holding clip (B) and the cable adjusting nut(A) after fixing the parking brake cable. |
5. | Install the parking brake pedal, and then install the parking brake pedal mounting bolts (A) and nuts (B).
|
6. | Adjust the parking brake pedal stroke by turning the adjusting nut (A).
|
7. | Reconnect the parking brake switch connector(A). |
8. | Install the juncting box. (Refer to the Body Electrical System group - Fuses and Relays) |
9. | Install the crash pad lower panel. (Refer to Body group - Crash pad) |
1. | Raise the vehicle, and make sure it is securely supported. |
2. |
3. | Remove the plug (A) from the disc. |
4. | Rotate the toothed wheel of adjuster by a screw driver until the disc is not moving, and then return it by 7~8 notches in the opposite direction. |
5. | Install the rear wheel & tire after installing the plug on the disc. |
1. | Operate the parking brake pedal through a full stroke over 3 times for setting the parking cables. |
2. | Adjust the adjusting nut(A) for parking barke pedal stoke 4~5 notches when operating effort is 196N(20kgf, 44lbf)
|
1. | Raise the vehicle, and make sure it is securely supported. |
2. | Loosen the mounting screws, then remove the console rear cover. |
3. | Adjust the parking brake lever stroke by turning adjusting nut (A).
|
4. | Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary. |
5. | Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully. |
6. |